A subdial on a
chronograph that can record time periods
of up to 12 hours.
30-Minute Recorder (or
Register):
A subdial on a chronograph (see "chronograph")
that can time periods up to 30 minutes.
A
Accuracy:
Refers to the rate constancy of watches, not only on whether it is showing the exact
time. A watch gaining or loosing exactly the same amount every day is considered
accurate.
Acrylic Crystal:
Sometimes referred to as Hesolite. This is an acrylic crystal composed of plastic
composite that is generally less expensive and less durable than a
sapphire or a
mineral crystal. Benefits of an acrylic
crystal are that it flexes rather than shatters on impact. It also produces
little glare under bright light and can be polished easily.
Alarm:
A device that makes a sound at a certain preset time. There are both
quartz and
mechanical alarm wristwatches.
Altimeter:
Function that provides your altitude by responding to changes in barometric pressure,
commonly found in pilot watches. Inside a pressurized airplane cabin, the
altimeter registers as if on land.
Analog Watch:
A watch with a dial,
hands, and numbers or markers that present a
total display of 12-hours of the day.
Analog-Digital Display:
A watch that shows the time by means of hands
(analog display) as well as by numbers (a digital display). The analog display
has a traditional dial with hour, minute and
sometimes second hands. The digital display shows the time numerically with a
liquid crystal display. This feature is usually found on sport watches.
Annual Calendar:
A watch showing the day, date month and 24 hours, adjusting automatically for
short and long months. The calendar needs
setting only once a year - at the end of February to the 1st of March.
Aperture:
Small opening. The dials of some watches (in
French: montres à guichet) have apertures in which certain indications are
provided (e.g. the date, the hour, etc).
Atmosphere (Atm):
Unit of pressure used in watch making to indicate
water resistance.
Atomic Time Standard:
Provided by the U.S. National Institute of Standards and Technology, Time and
Frequency Division, Boulder, Colorado, atomic time is measured through
vibrations of atoms in a metal isotope that resembles mercury. The result is
extremely accurate time that can be measured on instruments. Radio waves
transmit this exact time throughout North America and some 'atomic' watches can
receive them and correct to the exact time. To synchronize your watch with
atomic standard time, call (303) 499-7111.
Automatic Movement / Automatic Winding (also called
self-winding):
A mechanically powered watch that is wound by the motion of the wearer's arm
rather than through turning the winding stem
(manual mechanical). In response to this
motion, a rotor turns and winds the watch's
mainspring. Most automatic watches have up to 36 hours of power reserve. If an
automatic watch is not worn for a day or two, it will wind down and need to be
wound by hand to get it started again.
Click here for automatic watch instructions.
B
Band:
A vague, generic term used to refer to the band that holds a watch on your
wrist. The preferred terms bracelet and
strap, clearly describe the two major types.
Battery EOL:
Battery End Of Life indicator. This function forewarns of impending battery
failure in a quartz watch by means of the
second hand jumping in two or sometimes
four-second intervals. The wearer usually has approximately two weeks before
battery failure.
Battery Life:
The period of time that a battery will continue to provide power to run the
watch. Life begins at the point when the factory initially installs the battery
in the watch.
Battery:
A device that converts chemical energy into electricity. Most watch batteries
are the silver oxide type, delivering 1.5 volts. Much longer-lasting lithium
batteries deliver 3 volts.
Battery-less Quartz:
Also known under various marketing names, including
Kinetic (Seiko), Omega-matic (Omega), and
Auto quartz (Invicta). Terms for the modern hybrid watch technology of using a
quartz movement powered by a small electric
current generator operated by a rotor.
Electricity generated from the rotor's movement is stored in a capacitor,
rechargeable battery, or similar means to keep the watch running. So, like an
automatic watch, these also must be worn
regularly to keep up their electrical power reserve.
Bezel:
Generically, the upper part of the watch body. Specifically, it usually refers
to a ring around the outside of the crystal.
On jewelry watches, the bezel may contain a ring of diamonds. On sports watches,
the bezel may have calibrated markings and the ability to rotate in one or two
directions.
Bidirectional Rotating Bezel:
A bezel that can be moved either clockwise or
counterclockwise. These are used for mathematical calculations or for keeping
track of elapsed time.
Bracelet:
A bracelet is the flexible metal band
consisting of assembled links, usually in the same style as the
watchcase. Detachable links change the length
of the bracelet. Bracelets can be made of
stainless steel, sterling silver,
gold, or a combination. See also
strap.
C
Cabochon:
Used to indicate a smooth round or oval convex shaped polished gemstone. In
watch terminology, it describes a decorative stone set in the watch
crown.
Calendar:
The calendar mechanism or function on a watch can consist of a date only showing
in a window through to a triple calendar, showing the date, day and month. A
combination of dial cut outs and pointer hands
may be used. The most complicated calendar mechanisms may be mechanically
programmed to show the year and months including those with less that 31 days;
leap years can also be mechanically allowed for. Sometimes referred to as a
perpetual calendar.
Case or Watchcase:
The metal housing that contains the internal parts of a watch.
Stainless steel is the most typical metal
used, but titanium,
gold, silver
and platinum can also be used.
Chronograph Rattrapante:
The addition of a flyback hand (rattrapante)
significantly increases the potential uses for
chronographs. It makes possible the
measurement of split second times or timing
simultaneous events of unequal duration.
Chronograph:
A multifunction sport watch with a stopwatch
function. Most have two or three subdials,
or minidials, for measuring minutes and hours. When used in conjunction with
specialized scales on the watch dial it can
perform many different functions, such as determining speed or distance ( see
"tachometer" and
"telemeter"). Some can time more than one
event at a time (see "flyback hand" and
"split seconds hand"). Do not confuse with
"chronometer" which is a timepiece that
has met certain high standards of accuracy set by an official watch institute of
Switzerland.
Chronometer:
This term refers to a precision watch that is tested in various temperatures and
positions, thus meeting the accuracy standards set by
C.O.S.C. in Switzerland. These watches are
provided with a chronometer certifcate detailing specific test results by the
C.O.S.C.
Clasp:
The attachment used to connect the two ends of the watch
bracelet around the wrist.
C.O.S.C.:
Control Officile Suisse de Chronometers or Swiss Controle Officiel des
Cronometres- the independent Swiss regulatory organization that rigorously tests
and certifies (or fails) watch movements for
chronometer status.
Countdown Timer:
A function that lets the wearer keep track of how much of a preset period of
time has elapsed. Some countdown timers sound a warning signal a few seconds
before the time runs out. These are useful in events such as yacht races, where
the sailor must maneuver the boat into position before the start of a race.
Crown:
The crown often referred to as the winding crown or winder is used for
winding the watch in the
case of a non-automatic, for setting the
hands to the correct time and often for setting
the date in the case of calendar equipped
watches. On diving/sports models, the crown may be
screw-down whereby it screws onto a
threaded tube, which protrudes from the case of the watch. This often ensures
superior water resistance.
Crystal:
The cover over the watch dial is called the
crystal. There are three types of crystals commonly used in watches:
acrylic crystal is an inexpensive plastic
that allows shallow scratches to be buffed out.
Mineral crystal is composed of several elements that are heat-treated to
create an unusual hardness that aids in resisting scratches.
Sapphire crystal is the most expensive and
durable, approximately three times harder than mineral crystals and 20 times
harder than acrylic crystals. A non-reflective coating on some sport styles
prevents glare.
Crystal Skeleton Caseback:
Caseback made of transparent material such as hardened
mineral crystal or
sapphire crystal that reveals the intricate
movement of the watch.
Cyclops (Magnified
Window):
A small window or lens in the crystal that
is added to magnify the date 2 1/2 times.
D
Day/Date Watch:
A watch that indicates not only the date but also the day of the week.
Deployment Buckle (Foldover):
A three-folding enclosure that secures the two ends of the
bracelet and allows enough room for placing
the watch on the wrist when fully deployed. When closed, the buckle covers the
two-piece folding mechanism.
Depth Alarm:
An alarm on a diver's watch that sounds when
the wearer exceeds a preset depth. In most watches it stops sounding when the
diver ascends above that depth.
Depth Sensor/Depth Meter:
A device on a diver's watch that determines
the wearer's depth by measuring water pressure. It shows the depth either by
analog hands and a scale on the watch
dial or through a
digital display.
Dial:
The dial, often referred to as the face is
usually marked with numbers or batons to which the
hands point in order for the wearer to tell the correct time. Dials may be
minimalist with no markers at all or extremely complex as in the
case of pilots' chronographs. Dials may be
decorated with patterns or in some cases with precious stones.
Digital:
The display of time in numbers instead of hands
on the dial. The numbers can appear in an
LCD (Liquid Crystal Display), which shows a
continuous reading or an LED (Light-Emitting Diode), which shows the time at the
push of a button.
Display:
Indication of time or other data, either by means of
hands moving over a
dial (analog
display) or by means of numerals appearing in one or more windows (digital
or numerical display); these numerals may be completed by alphabetical
indications (alphanumerical display) or by signs of any other kind. Example:
12.05 MO 12.3 = 12 hours, 5 minutes, Monday 12th March. Such displays can be
obtained by mechanical or electronic means.
Diver's Watch:
Divers' watches traditionally feature a graduated,
rotating bezel,
screw down winding crown, and caseback...
must be water resistant to at least 200m or
660 feet.
Dual Time/Second Time Zone Bezel:
A rotating bezel, which can be used to
display a separate time zone distinct from that shown on the
dial.
Dual Time:
A watch that measures current local time as well as at least one other time
zone. The additional time element may come from a twin dial, extra
hand, subdial,
or other means.
E
Elapsed Time Rotating Bezel:
A graduated rotating bezel (see "rotating
bezel") used to keep track of periods of time. The bezel can be turned so
the wearer can align the zero on the bezel with the watch's seconds or minutes
hand. You can then read the elapsed time off of
the bezel. This saves from having to perform the subtraction that would be
necessary if you used the watch's regular dial.
Elapsed Time:
The actual time taken for an object to travel over a specified distance.
Engine Turning:
Decorative engraving, usually on a watch dial.
EOL:
End of Life. In quartz movement, the end of
battery life is indicated by the second hand,
which starts to jump every four seconds. The battery should be changed
immediately.
F
Face:
The visible side of the watch or the dial.
Flyback:
An additional hand on a
chronograph which moves with the second
hand but, can be stopped independently to measure an interval which can then
"fly back" to catch up with the other hand. This is useful for capturing lap
times without losing the ability to capture the finish time.
Foldover Buckle (Deployment):
A three-folding enclosure that secures the two ends of the
bracelet and allows enough room for placing
the watch on the wrist when fully deployed. When closed, the buckle covers the
two-piece folding mechanism.
G
Gasket:
A rubber or plastic ring that seals the internal works of the watch against
dust, moisture and water.
GMT Timezone:
GMT (Greenwich Mean Time), also known as Zulu Time, as set to the international
clock in Greenwich, England, reflects, through an additional hour
hand, the world time on a 24-hour scale and is
used by pilots worldwide.
Gold Plating:
An application of gold over the surface of an item.
Gold, Rose Gold, Yellow Gold, and White Gold:
The only natural form of gold is yellow gold. But since gold is too soft in its
pure form to make jewelry, it is normally made into an alloy by mixing it with
other metals. The portion of pure gold to other metals determines the Karat
rating. 24K is pure gold. 18K is 75% pure. The exact nature of the other metals
used determines the color. A moderate amount of copper in the alloy creates Rose
Gold. A moderate amount of palladium and nickel creates white gold.
H
Hand:
Indicator, usually made of a thin, light piece of metal, variable in form, which
moves over a graduated dial or scale. Watches
usually have three hands showing the hours, minutes and seconds.
Handwinding (Manual Mechanical):
A watch with a manual mechanical movement, which needs to be wound by the wearer
using the winding crown. This winds the
mainspring up which then releases its energy to power the watch.
J
Jewels:
The bearing, endstone or pallet used for reducing friction within the
movement of a watch are made of synthetic
material of precious or semi-precious stones. Usually a very inexpensive form of
synthetic ruby, these are used for virtually frictionless pivots or hubs at
certain critical places in the watch mechanism. These jewels do not add any
monetary value to a watch. It is also important to understand that more jewels
does not necessarily make a better watch.
Jump Hour Indicator:
A jump hour indicator takes the place of an hour
hand. It shows the hour by means of a numeral in a window on the
dial of the watch. The word "jump" refers to
the fact that the numerals jump from 1 to 2 to 3, etc., rather than showing
intermediate times between hours as hour hands do. The minutes and seconds in a
jump hour watch are read as normal from the analog hands and dial.
K
Karat or K:
An indication of the purity of the metal used, expressed in the number of 1/24th
of the pure metal used in the alloy. Metals such as
gold are too soft in their pure state use in jewelry, so they are typically
made into an alloy with other metals for strength. 24K (equal to 24/24ths) is
pure metal. 18K is 18 parts pure metal mixed with 6 parts of other metals. That
translates to 18/24=0.750, which is 75% pure, or 750 parts per thousand.
Kinetic:
Refers to the Seiko line of Kinetic watches. This innovative technology has a
quartz movement that does not use a battery.
Movement of your wrist charges a very efficient capacitor which powers the
quartz movement. Once the capacitor is fully charged, men’s models will store
energy for 7-14 days without being worn. Ladies models store energy for 3-7
days. The watch alerts you to a low capacitor charge when the seconds
hand starts to move in two second intervals.
L
Lap Memory:
The ability, in some quartz sport watches, to
preserve in the watch's memory the times of laps in a race that have been
determined by the lap timer (see "lap timer").
The wearer can recall these times on a digital
display by pushing a button.
Lap Timer:
A chronograph function that lets the
wearer time segments of a race. At the end of a lap, the wearer stops the
timer, which then returns to zero to begin
timing the next lap.
LCD Display (Liquid Crystal Display):
A digital watch
display that shows the time electronically
by means of a liquid held in a thin layer between two transparent plates.
Followed from the earlier LED or Light Emitting Diode display of the first
quartz digital watches. The LCD was preferred as it used vastly less power than
the LED thus the time could be shown constantly as opposed to having to press a
button for time display.
Lugs:
Extensions on both sides of the case where the
bracelet or
strap is attached.
M
Magnified Window (Cyclops):
A small window or lens in the crystal that
is added to magnify the date 2 1/2 times.
Manual Winding:
Refers to a watch with a manual mechanical
movement, which needs to be wound by the wearer using the winding
crown. This winds the mainspring up which then
releases its energy to power the watch.
Mechanical Movement:
A movement based on a mainspring which when wound slowly unwinds the spring in
an even motion to provide accurate timekeeping. As opposed to a
manual mechanical watch which needs to be
wound on a consistent basis, an automatic
mechanical requires no winding because of the
rotor, which winds the mainspring every time you move your wrist (see our
section on
automatic watch maintenance for more details).
Military or 24 Hour Time:
When time is measured in 24-hour segments. To convert 12-hour time to 24-hour
time, simply add 12 to any p.m. time. To convert 24-hour time to 12-hour time,
subtract 12 from any time from 13 to 24.
Mineral Crystal:
Watch crystal made from what is essentially
a form of glass. More scratch resistant than
acrylic, a mineral crystal will however scratch and is extremely difficult
to polish.
Minute Repeater:
A Complication on a watch that can strike the time in hours, quarters, or
seconds by means of a push piece.
Moon Phase:
An indicator that keeps track of the phases of the moon. A regular rotation of
the moon is once around the earth every 29 days, 12 hours and 44 minutes. Once
set, the moon phase indicator accurately displays the phase of the moon.
Mother-of-Pearl:
Iridescent milky interior shell of the freshwater mollusk that is sliced thin
and used on watch dials. While most have a milky white luster, mother-of-pearl
also comes in other colors such as silvery gray, gray blue, pink and salmon.
Movement:
The means by which a watch keeps time, often including the power source. For
example, a watch with mechanical movement
uses a spinning balance wheel powered by a tightly wound spring, whereas a watch
with quartz movement measures the vibrations
in a piece of quartz and often is powered by a battery.
O
O-Ring:
O-rings are used to seal the backs of watches, which feature either a press-in
back or a screw on back. They ensure water
resistance. Usually also used on the
winding stems of watches and in the winding
crowns to protect against the ingestion of water and dust. Normally made
from a rubber/plastic compound.
P
Pedometer:
A device that counts the number of strides taken by the wearer by responding to
the impact of the wearer's steps.
Perpetual Calendar:
A calendar complication that adjusts
automatically to account for different lengths of the month (30 or 31 days) and
leap years. Perpetual calendars, which can be powered by
quartz or
mechanical movements, are programmed to be accurate until the year 2100.
Platinum:
One of the most rare precious metals, platinum also is one of the strongest and
heaviest, making it a popular choice for setting gemstone jewelry and watches.
It has a rich, white luster, and an understated look. Platinum is hypoallergenic
and tarnish resistant. Platinum used in jewelry and watches is at least 85 to 95
percent pure. Many platinum watches are produced in limited editions due to the
expense and rarity of the metal.
Power Reserve Indicator:
A feature that shows when the watch will soon need a new battery or
winding. A battery reserve indicator on a
quartz watch informs the wearer when the
battery is low. Often this is indicated by the seconds
hand moving at two or three-second intervals.
Seiko's Kinetic watches are quartz watches that do not have a battery (see
Kinetic). When a Seiko Kinetic needs to be
wound, the seconds hand will also move in two-second intervals.
Power Reserve:
A measure of the amount of time a watch will run after being fully powered or
wound, with no additional power input. Normally, this means when a
mechanical watch is fully wound or a
quartz watch has a brand new battery. Many
modern mechanical watches have a power reserve of 40 hours. Power reserve also
applies to battery-less quartz watches, which may have power reserves from 40
hours to 6 months. On battery-operated quartz watches, the term is sometimes
used to refer to the expected battery life--typically 12 to 32 months.
Pulsimeter:
A scale on a chronograph watch for
measuring the pulse rate.
Push-Piece:
Button that is pressed to work a mechanism. Push-pieces are usually found on
chronographs, striking watches, and
alarms.
Q
Quartz:
A caliber that uses the vibrations of a tiny crystal to maintain timing
accuracy. The power comes from a battery that must be replaced about every 2-3
years. In recent years, new quartz technology enables the watch to recharge
itself without battery replacement. This power is generated via body motion
similar to an automatic mechanical watch,
or powered by light through a solar cell (Kinetic
& solar-tech).
R
Ratchet Bezel Ring:
A bezel ring that can either turn one way
(counter clockwise) or both ways and generally clicks into place.
Rattrapante Chronograph:
The addition of a flyback hand (rattrapante)
significantly increases the potential uses for
chronographs. It makes possible the
measurement of split second times or timing
simultaneous events of unequal duration.
Register:
Another name for a subdial; this is usually
a dial within the main dial of a watch. The
best example is possibly a chronograph
where there may be registers for the chronograph minutes and hours. Some watches
have registers with pointers showing the day and date.
Repeater:
A device that chimes the time when the wearer pushes a button. Some repeaters,
called "quarter repeaters" sound just the hours and the quarter hours ( by means
of two different pitched tones); others called "five minute repeaters", sound
the hours, quarters, and five minute periods after the quarter; and still others
called "minute repeaters", sound the hours,
quarters and minutes.
Retrograde:
Used to describe a pointer hand on a watch
dial (often a
subdial), which returns to zero at the end of a prescribed period. For
example a watch may have retrograde date - in this case the hand moves up a
scale a day at a time, pointing to the current date - when it reaches 31 it will
spring back to 1
Rhodium Plated:
Protective coating of metal with a thin layer of rhodium; hard, brittle metal
which does not oxidize and is malleable only when red hot.
Rose (or pink) Gold:
A softly hued gold that contains the same
metals as yellow gold but with a higher
concentration of copper in the alloy. A popular color in Europe, rose gold in
watches is often seen in retro styling or in tricolor gold versions. Some 18k
red gold watches achieve their color from additional copper in the alloy.
Rotating Bezel:
A bezel (the ring surrounding the watch
dial) that can be turned. Different types of
rotating bezels perform different timekeeping and mathematical functions.
Rotor:
The part of an automatic (or self-winding)
mechanical watch that winds the movement's mainspring. It is a flat piece of
metal, usually shaped like a semicircle, which swivels on a pivot with the
motion of the wearer's arm.
S
Sapphire Crystal:
Synthetic sapphire formed for use as the crystal
of a watch. Extremely scratch resistant (9 on the Moh scale), a sapphire crystal
is the material of choice for many watch collectors. The downsides are that
sapphire can chip at the edges if they protrude and can shatter.
Sapphlex Crystal (Seiko Watches):
Highly scratch resistant crystal created by
the fusion of sapphire and
mineral glass crystal.
Screw-Down Locking Crown:
A crown that aids
water resistance by sealing the crown to the
case of the watch. The seal is achieved by the matching of a threaded pipe on
the case with the crown's internal threads and
gaskets, while twisting the crown to lock it into place.
Second Time Zone Indicator:
An additional dial that can be set to the time
in another time zone. It lets the wearer keep track of local time and the time
in another country simultaneously.
Self-Winding:
This term refers to a mechanically powered watch that is wound by the motion of
the wearer's arm rather than through turning the
winding stem (manual
mechanical). In response to this motion, a
rotor turns and winds the watch's mainspring. Most automatic watches have up
to 36 hours of power reserve. If an automatic watch is not worn for a day or
two, it will wind down and need to be wound by hand to get it started again.
Click here for automatic watch instructions.
Shock Resistance:
As defined by the U.S. government regulation, a watch's ability to withstand an
impact equal to that of being dropped onto a wood floor from a height of three
feet.
Slide Rule Bezel:
A rotating bezel, or ring, around the
outside edge of the watch case that is printed
with a logarithmic scale and assorted other scales and is used in conjunction
with fixed rules of mathematics to perform general mathematical calculations or
navigational computations.
Solar Powered:
A type of quartz movement where the batteries
are recharged via solar panels on the watch dial.
They have a power reserve so they can run even in the dark.
Solar Tech:
Solar powered quartz watch. This technology
provides the accuracy of quartz, without the inconvenience and cost of regular
battery changes.
Split Second:
A feature on a chronograph that actually
is two hands, one a
flyback, the other a regular hand. To time
laps or different finishing times, the wearer can stop the fly backhand
independently while the regular hand keeps moving.
Stainless Steel:
An extremely durable metal alloy (chromium is a main ingredient) that is
virtually immune to rust, discoloration, and corrosion; it can be highly
polished, thus resembling a precious metal. Stainless steel is often used even
on case backs on watches made of other metals and is the metal of choice used to
make high quality watchcases and
bracelets. It is also hypoallergenic
because it doesn't contain nickel.
Sterling Silver:
A precious metal. Sterling refers to silver that is 92.5 percent pure. The
silver fineness should be stamped on the metal, sometimes accompanied by the
initials of a designer or country of origin as a hallmark. A protective coating
may be added to prevent tarnishing.
Stopwatch:
A watch with a seconds hand that measures
intervals of time. When a stopwatch is incorporated into a standard watch, both
the stop watch function and the timepiece are referred to as a
"chronograph".
Strap:
A watchband made of cloth, rubber, leather or other non-metal material.
Subdial:
A small dial used for any of several purposes,
such as keeping track of elapsed minutes or hours on a
chronograph or indicating the date.
Swiss A.O.S.C. (Certificate of Origin):
A mark identifying a watch that is assembled in Switzerland with components of
Swiss origin, primarily used in Bedat watches.
T
Tachometer (Tachymeter):
Instrument for measuring speed or units. In watch making, a
timer or
chronograph with a graduated dial on which
speed can be read off in kilometers per hour or some other unit (see
timer).
Tank Watch:
A rectangular watch with heavier bars on either side of the
dial. Inspired by the tank tracks of World War
I and first created by Louis Cartier.
Tantalum:
A metal with a texture similar to titanium,
but a color similar to gold. Used by Omega for
the gold-like trim on certain titanium watches. Many of these watches are also
available in titanium with real gold trim.
Telemeter:
A watch function that finds the distance of an object from the wearer by
measuring how long it takes sound to travel the distance. Like a
tachometer, a telemeter consists of a
stopwatch function and a special on the
dial of a
chronograph.
Timer:
Instrument used for registering intervals of time (duration, brief times),
without any indication of the time of day.
Titanium:
A "space age" metal, often having a silver-gray appearance. Because it is 30
percent stronger and nearly 50 percent lighter than steel, it has been
increasingly used in watch making, especially sport watch styles. Its resistance
to salt water corrosion makes it particularly useful in
diver's watches. Since it can be scratched
easily, some manufacturers use a patented-coating to resist scratching. Titanium
is also hypoallergenic.
Tonneau Watch:
A watch with a barrel-shaped watchcase and two
convex sides.
Totalizer:
A mechanism that keeps track of elapsed time
and displays it, usually on a subdial on the
watch dial. Same as a "recorder" or
"register". The term "totalizer" can be
used more generally to refer to any counter on a watch.
U
Unidirectional Rotating Bezel:
An elapsed time rotating bezel,
often found on divers watches, that moves
only in a counterclockwise direction. It is designed to prevent a diver who has
unwittingly knocked the bezel off its original position from overestimating his
remaining air supply. Because the bezel only moves in one direction, the diver
can err only on the side of safety when timing his dive. Many are ratcheted, so
that they lock into place for greater safety.
UTC:
Universal Time Coordinated. A universal time based on the Greenwich Meridian
used by the military and in aviation. Greenwich Mean
Time (GMT) can be considered approximately equivalent to Universal Time
Coordinated (UTC). GMT as such is now obsolete however, being replaced by UTC.
Using this timezone/standard avoids errors and problems associated with
different time zones and summer times operational in different countries.
W
Water Resistance:
Describes the level of protection a watch has from water damage. See the
"water resistance" section for a description of the different levels.
Waterproof:
The ability to completely exclude the possibility of water entering into any
working portion of a watch. According to the Federal Trade Commission, no watch
is fully 100 percent waterproof and no manufacturer that sells watches in the
U.S. may label any of their watches "waterproof." The FTC demands that watches
only be referred to as "water resistant."
Winding Stem:
The button on the right side of the watchcase
used to wind the mainspring. Also called a
"crown."
Winding:
Operation consisting of tightening the mainspring of a watch. This can be done
by hand (by the crown) or automatically (by a
rotor, which is caused to swing by the
movements of the wearer's arm).
World Time Dial:
A dial, usually on the outer edge of the watch
face, which tells the time up to 24 time zones
around the world. The time zones are represented by the names of cities printed
on the bezel or dial. The wearer reads the hour in a particular time zone by
looking at the scale next to the city that the hour
hand is pointing to. The minutes are read as normal. Watches with this
feature are called "world timers."
Y
Yacht Timer:
A countdown timer that sounds warning signals
during the countdown for a boat race.